（请投标商特别注意：本项目为全流程电子化招标，招标文件和CA数字认证证书请于中国航发网上商城电子招投标专区购买，CA数字认证证书请务必购买，否则无法进行线上开标。具体请参看中国航发网上商城电子招投标专区发布的相关指南，谢谢！）*. 招标条件本招标项目高温摩擦磨损实验器资金已落实。该项目已具备招标条件，现对高温摩擦磨损实验器进行国际公开招标。*. 项目概况与招标范围项目概况与招标范围： 高温摩擦磨损实验器 *套招标项目编号：****-*****E******/**招标项目名称：高温摩擦磨损实验器数量：*套*. 投标人简要技术及资格要求*.* 简要技术：（*）*Z向试样定位控制系统的最大行程：不小于***mm；可以进行原位磨损深度检测，精度≤*μm； （*）*加载力范围*mN~****N。 （*）*加载模式：可以实现精密加载，通过编程控制，可实现线性、台阶、恒定等加载模式；运动模块：可实现高温、高湿、盐雾环境下的线性往复、旋转、环块、微动等加载方式； （*）*高速线性往复运动模块：可调冲程：*.*mm~**mm，速度（频率范围）：*.*~**Hz；其中*.*~*mm冲程时，频率≥**Hz；包括液体容器和安装测试样品； （*）*高速旋转模块：最高转速：≥****rpm （*）*高扭矩环块模块：最高转速：≥****rpm （*）*高速旋转驱动高温腔：可拆卸，腔内温度调节范围至少是室温到****℃ （*）*高速线性往复驱动高温腔：可拆卸，腔内温度调节范围至少是室温到****℃ （*）*高速旋转驱动低温腔：可拆卸，需配制冷机、低温控制器，可进行低温条件下的测试。腔内最低温度至少可以控制在-**℃ （**）*高速线性往复驱动低温腔：可拆卸，需配制冷机、低温控制器，可进行低温条件下的测试。腔内最低温度至少可以控制在-**℃ （**）*高速线性往复驱动湿度腔：可拆卸，需配湿度控制器，湿度控制器程序控制，范围：*~**%RH仅与湿度腔连用； （**）*二维伺服控制力学传感器（Fx/Fz），Fx和Fz力传感器范围：*～***mN；Fx和Fz分辨率不低于**μN，*个； （**）*二维伺服控制力学传感器（Fx/Fz），Fx和Fz力传感器范围：*.*～**N；Fx和Fz分辨率不低于*mN，*个； （**）*二维伺服控制力学传感器（Fx/Fz），Fx和Fz力传感器范围：*~***N；Fx和Fz分辨率不低于**mN，*个； （**）*二维伺服控制力学传感器（Fx/Fz），Fx和Fz力传感器范围：***～****N；Fx和Fz分辨率不低于***mN，*个； 资格业绩要求： （*）**）设备制造厂商在国内应具有五台或五台以上与投标设备同型号的高温摩擦磨损实验器的销售业绩，并在投标文件中提供用户清单和相关合同复印件等证明材料。设备制造厂商有丰富仪器研发和制造经验，注册成立时间不少于**年，需在投标文件中提供注册证明文件。投标人应在投标文件中提供制造商针对本项目的正式授权函原件。*）一旦中标，投标人必须是与买方签订本项目外贸合同的签约方。如投标人不具备与买方签订外贸合同的能力，其投标将被否决。*.* 本次招标不接受联合体投标。*. 招标文件的获取*.* 招标文件购买时间： ****-**-** **:**至****-**-** **:***.* 招标文件购买地址：中国航发网上商城 http://***.******.***/*.* 招标文件价格:RMB**** /USD *** ，售后不退。*. 投标文件的递交*.* 投标文件递交截止时间： ****-**-** **:***.* 投标文件递交地点： 纸质版文件递交至北京市远大中心（北京市朝阳区慧忠路*号远大中心B座**层），电子文件递交到中国航发网上商城电子招投标专区（http://***.******.***）*.* 逾期送达的、未送达指定地点的或者不按照招标文件要求密封的投标文件，招标人将予以拒收。逾期送达的投标文件，电子招标投标交易平台将予以拒收。*. 开标时间及地点*.* 开标时间： ****-**-** **:***.* 开标地点： 北京市远大中心（北京市朝阳区慧忠路*号远大中心B座**层）现场开标/中国航发网上商城电子招投标专区（http://***.******.***）网上开标*. 发布公告的媒介本次招标公告同时在中国招标公共服务平台和中国航发网上商城电子招投标专区 http://***.******.***/ 上发布。*. 联系方式招 标 人：招标代理机构：中******地 址：地 址：北京市朝阳区慧忠路*号远大中心B座**层邮 编：邮 编：******联系人：联系人：鲁璐电 话：电 话：***-********传 真：传 真：***-********电子邮件：电子邮件：ll@aited.cn网址：网址：开户银行：开户银行：账号：账号： ****年**月**日(Please pay special attention to bidders: this project is an electronic bidding for the whole process, and the bidding documents are requested to be purchased on the http://***.******.***/ Please refer to the relevant guidelines issued on the http://***.******.***/, thank you!).*. Bidding ConditionsThe name of the tenderee of the project is High Temperature Friction & Wear Tester . Source of Funds has been carried out. The project is qualified for bidding conditions, and invites sealed bids from eligible suppliers home and abroad for the supply of High Temperature Friction & Wear Tester (The name of the equipment) by way of International Competitive Bidding.*. Overview and ScopeOverview and Scope：High Temperature Friction & Wear Tester One SetBidding No.：****-*****E******/**Project Name：High Temperature Friction & Wear TesterQuantity：One Set*. Qualification Requirements For Bidder*.* Main Technical Data：(*)*Z-direction sample positioning and control system’s maximum travel: not less than *** mm, and can carry out measurement of original position wearing depth, the accuracy ≤ * μm. (*)*Loading force range: *mN~****N. (*)*Loading mode: Precision loading should be available and linear, stepping, constant loading method should be feasible by means of programed control.Motion module: Linear reciprocating, rotating, ring-block, and micro-motion loading modes and other loading modes under high temperature, high humidity and salt fog environment should be available. (*)*High speed linear reciprocating motion module:Adjustable travel: *.* mm ~ ** mm Speed (frequency range): *.* Hz~ ** Hz For the travel of *.* mm~* mm, the frequency should be **Hz or higher Liquid containers and test samples to be mounted should be provided. (*)*High-speed rotating module: Max. speed: ≥ *,*** rpm (*)*High torque ring-block module: Max. rotating speed: ≥ *,*** rpm (*)*High-speed rotating drive high-temperature chamber: detachable, with the temperature range inside the cavity at least reaching the room temperature of *,***℃. (*)*High-speed linear reciprocating drive high-temperature chamber: detachable, with the temperature range inside the cavity at least reaching the room temperature of *,***℃ (*)*High speed rotating drive low-temperature chamber: detachable Refrigerators and low temperature controllers should be provided to conduct tests at low temperatures. The minimum temperature in the chamber should be controlled to be within -**℃ (**)*High-speed linear reciprocating drive low-temperature chamber: detachable Refrigerators and low temperature controllers should be provided to conduct tests at low temperatures. The minimum temperature in the chamber should be controlled to be within -**℃ (**)*High speed linear reciprocating drive humidity chamber: detachable Humidity controllers should be provided and under programmed control. The control range should be *%~**%RH. Only connection with the humidity chamber should be allowed. (**)*Two-dimensional servo control mechanical sensor (Fx/Fz), Fx and Fz force sensor range: * mN ~ *** mN; Fx and Fz resolution ≥ ** μN, * piece; (**)*Two-dimensional servo control mechanical sensor (Fx/Fz), Fx and Fz force sensor range: *.* N~ **N; Fx and Fz resolution ≥ * mN, * piece; (**)*Two-dimensional servo control mechanical sensor (Fx/Fz), Fx and Fz force sensor range: * N ~ *** N; Fx and Fz resolution ≥ ** mN, * piece; (**)*Two-dimensional servo control mechanical sensor (Fx/Fz), Fx and Fz force sensor range: *** N~ **** N; Fx and Fz resolution ≥ *** mN, * piece; Qualification requirements : (*)**) The equipment manufacturer should have a sales performance of five or more high temperature friction & wear testers of the same model as the bid equipment in China, and should provide the user list and copies of relevant contracts and other supporting materials in the bidding document. The equipment manufacturer should have rich experience in instrument research, development and manufacture, and a history of at least ** years; its registration certificates must be provided in the bidding document. The bidder shall provide original official authorization of the manufacturer in view of this project in the bidding documents. *) The bidder must be the contractor that has signed with vendee the contract on foreign trade for this project once the bid has been won. If the bidder is not qualified to sign with the vendee the contract on foreign trade, the accepted bid shall be ***.******.*** Joint Bids:NOT Available*. Acquisition of Bidding Documents*.*Time of Selling Bidding Documents：****-**-** **:**to****-**-** **:***.* Place of Selling Bidding Documents：AECC Online Shopping Mall E-bidding Zone (http://***.******.***)*.* Price of Bidding Documents: RMB**** /USD *** , with non-refundable*. Bid Submission*.* Deadline for Submitting Bids：****-**-** **:***.* Place for Submitting Bids： Paper-edition tender documents must be delivered to Beijing Grand Place (** Fl., Tower B, Grand Place, No.* Hui Zhong Road, Chaoyang District, Beijing), E-edition tender documents must be delivered to AECC Online Shopping Mall E-bidding Zone (http://***.******.***) *.* The tenderee will refuse to accept the tender documents that are not delivered to the designated place within the specified time or fail to be sealed according to the requirements of the bidding documents. The tender documents for overdue delivery will be rejected by the electronic tendering and bidding transaction platform.*. Time and Place of Bid Opening*.* Time of Bid Opening：****-**-** **:***.* Place of Bid Opening：Beijing Grand Place (** Fl., Tower B, Grand Place, No.* Hui Zhong Road, Chaoyang District, Beijing) by onsite bid opening/AECC Online Shopping Mall E-bidding Zone (http://***.******.***) *. Media for NoticeThe tender notice is issued both on China Tendering And Bidding Public Service Platform and AECC Online Shopping Mall E-bidding Zone (http://***.******.***).*. Contact DetailsName of Tenderee：Name of Tendering Agent：AVIC International Trade and Economic Development LtdAdd.：Add.：** Fl., Tower B, Grand Place, No.* Hui Zhong Road, Chaoyang District, Beijing, PRCPost code：Post code：******Contact：Contact：LULUTel：Tel：***-********Fax：Fax：***-********Email：Email：******：Website：Bank and Account (CNY) ：Bank and Account (CNY) ：Bank and Account (USD) ：Bank and Account (USD) ： ****-**-**